Minka Lavery 4939-284 Manuale delle Istruzioni Scaricare il pdf

INSTALLATION INSTRUCTIONS FOR FIXTURE #4939

ASSEMBLING THE FIXTURE (FIG. 2)

1. Shut off the power at the fuse box or circuit breaker. If

necessary, remove the old fixture including the mounting

hardware.

2. Carefully remove the new fixture from the carton and check that

all parts are included as shown in the illustration.

3. Thread the fixture loop (A) tightly onto the nipple (B).

4. Adjust the fixture arms to their proper position.

5. Place the glass shade (E) over the socket (F), then secure with

the cushion ring (D) and socket ring (C).

6. Install the light bulb in accordance with fixture’s specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE

PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

MOUNTING THE FIXTURE (FIG.1)

1. Thread the nipple (S) into the collar loop (T) until snug.

2. Thread the other end of nipple (S) into the cross bar (P).

The side of the cross bar marked with “GND” must face out.

3. Place lock washer (Q) over the end of nipple (S) protruding

through cross bar (P) and thread hex nut (R) onto nipple (S) until

tight.

4. Take this crossbar assembly and mount to ceiling outlet box (V)

tightly using outlet box screws (W).

5. Use proper chain pliers to open one end link of the chain and

connect to the fixture loop (A). Close the link.

6. By measuring, determine the correct number of links needed for

proper hanging height. Using the chain pliers, disconnect and

discard the remaining chain.

7. Carefully lace the fixture wires through the chain (X).

8. Slip collar ring (Y) over the chain (X), then do the same with

canopy (U).

9. Open the other end link of the chain (X) and connect to the collar

loop (T). Close the link.

10. Feed the fixture wires through the collar loop (T) and nipple (S)

and pull until tight.

CONNECTING THE WIRE (See Wiring Diagram)

1. At this point, connect the electrical wires as shown in the wiring

diagram, making sure that all wire connectors are secured. If

your outlet box has a ground wire (green or bare copper),

connect the fixture’s ground wire to it. Otherwise, connect the

fixture’s ground wire directly to the cross bar using the green

screw provided.

2. Tuck these wires connectors neatly into the ceiling outlet box

and raise the collar ring (Y) and thread onto collar loop (T)

protruding through the canopy.

Your installation is now complete. Return power to the outlet box

and test the fixture.

Notice: It is important to use proper chain pliers (not

included) to OPEN and CLOSE the chain included with

this fixture. Do not open them with other tools that may

twist or stress the chain links. It is important to use

proper chain pliers like the ones shown in the diagram.

GLASS SHADE(E)

SOCKET(F)

LOOP(A)

NIPPLE(B)

FIXTURE BODY

Fig. 2

Fig. 1

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

(SKT-RING-26)

Set A#A-010

-Crossbar

-Ground Screw

-Mounting screws (2)

Chain # HCH3072-281

Gauge 4.5MM

NIPPLE(B) 1

Sommario

Pagina 1 - NIPPLE(B)

INSTALLATION INSTRUCTIONS FOR FIXTURE #4939ASSEMBLING THE FIXTURE (FIG. 2)1. Shut off the power at the fuse box or circuit breaker. Ifnecessary, remov

Commenti su questo manuale

Nessun commento

Minka Lavery 4939-284 Manuale delle Istruzioni

Navigare online o scaricare Manuale delle Istruzioni per no Minka Lavery 4939-284. Minka Lavery 4939-284 Instructions / Assembly Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi no Minka Lavery 4939-284